LILYGO® Shipping to worldwide
T-Echo Plus
T-Echo Plus
4.0 / 5.0
(4) 4 total reviews
Couldn't load pickup availability
Share
About Shipping
About Shipping
Methods & Delivery Time
- Standard Express: 25-30 Days
- YunTu Express : 10-20 Days
(Company name can't be used consignee) - DHL: 10-17 Days
- FedEx: 10-17 Days
Please note that all delivery times are estimated for reference only.
Check More Info: Shipping Policy
About Tax
About Tax
We only charge the product cost and shipping cost.
1. For Standard Express Order: You may not need to deal with customs clearance, just need to pay attention to the track of the parcel, but this is not absolute, if your parcel is inspected by the customs, then you need to assist in dealing with customs clearance.
2. For DHL/ FedEx Order: You need to deal with the relevant customs clearance matters, as well as pay the tariff, the specific amount of tariff please pay attention to the policy of your country.
----------------------
The above tariffs are for reference only, please pay attention to your country's tax policy for more detailed instructions, if you need our help or have questions please feel free to contact us.
Key Feature Upgrades
- ✅BHI260AP IMU — Improved motion sensing
- ✅Vibration Motor — Tactile feedback
- ✅2400mAh Battery — Extended usage
- ✅Buzzer — Audible alerts
Structural Improvements
- 1/4-inch Mount Interface
- Climbing Finger Loop

Specification
| MCU | NRF52840 |
| FLASH | 2MB |
| RAM | 2MB |
| Bus Interfaces | UART, SPI, TWI, PDM, 12S, QSPI |
| Wireless Connectivity |
Bluetooth 5, Thread, Bluetooth Mesh, ANT, 802.15.4, Zigbee With/ Without BME280 temperature pressure sensor |
| SX1262 LoRa Transceiver |
Long Range, Low Power Global frequency coverage 433, 868, 915Mhz |
| Battry Capacity | 2400mAh |
1.54-inch SPI E-Paper Display
| Grey level | 2 |
| Resolution | 200x200 |
| Full refresh time | 2S |
L76K Multi-System Positioning GNSS module
| Support System | GPS, GLONASS, BeiDou, QZSS |
Tech Support
|
ℹ️Firmware 1. LILYGO Check out GitHub repository for sample code and more detailed information about this board. 💻LILYGO GitHub Community |
What's In The Box


-
Who can use
It's easier to master these development boards with a basic programming knowledge [engineers/ students/ makers, etc..]
-
Accelerated processing
International orders please make sure your address is in English
For Hong Kong, Macau and Taiwan orders, please note your personal ID. -
Got a question
Click on the bubble in the bottom right corner where some frequently asked questions are answered, or just drop us a line.
T-Echo Plus
Installed meshcore firmware, works fine
Probably going to be my go-to camping Meshtastic node, the buzzer and the vibration motor are a nice addition, I'm not sure how useful the IMU is currently but I can probably think of something eventually. Note that I bult my own firmware for the device, the additional features (Vibration motor and IMU) are not currently officially supported but may be in the future. The buzzer can be enabled.
Flashed Meshtastic to this device, and the screen is reversed and can’t be reset. Don’t buy this if you want to do Meshtastic.
Hi Kevin,
Thank you for your feedback.
We'd like to clarify that the T-Echo Plus and T-Echo share the same mainboard.
Therefore, the core component is fully compatible with Meshtastic.
Regarding the screen inversion issue you mentioned, this is typically a setting that can be adjusted. Based on your description, we believe there might be some confusion in using the buttons to navigate the menu.
Here is the correct procedure:
---Press and hold the button to wake up the device or confirm a selection.
---Short press the button to cycle through or select menu options.
--------------
To help you visualize this, we will send you a short instructional video shortly. Please keep an eye on your messages.
If the issue persists after following these steps, please reply directly to this message, and our team will assist you with further troubleshooting.
Thank you for your patience.
